The Most Successful Downhill Bike of All Time, Reinvented.

Want to pedal your way to the DH track? Check out the Nomad

Proud owner of a new V10? Take a minute to register it with us. 

Key Features:

  • Wheel size: 27.5"
  • Rear travel: 216mm

The All-New Santa Cruz V10

Geometry & Sizing

Rollover table below to highlight frame dimensions.

High Setting

The V10 has two geometry settings, which are easily adjustable with a 6mm hex wrench. The 'high' setting results in a 64-degree head tube angle, and the 'low' setting slackens it by a half-degree and drops the bottom bracket by a quarter-inch for even more stability at higher speeds.

All measurements reflect installation of a fork with a 586.1mm axle-to-crown height.

SMLXLXXL
Reach383.3mm15.09"402.5mm15.85"423.8mm16.69"450.8mm17.75"475mm18.7"
Stack592.4mm23.32"592.4mm23.32"601.3mm23.67"610.4mm24.03"619mm24.37"
Head Tube Angle64°64°64°64°64°64°64°64°64°64°
Seat Tube Length444.5mm17.5"457.2mm18"463.6mm18.25"469.9mm18.5"470mm18.5"
Front Center
BB Height360mm14.17"360mm14.17"360mm14.17"360mm14.17"360mm14.17"
BB Drop
Wheelbase1172.9mm46.18"1192.2mm46.94"1217.8mm47.94"1249.2mm49.18"1278mm50.31"
Chainstay Length440mm17.32"440mm17.32"440mm17.32"440mm17.32"450mm17.72"
Head Tube Length100mm3.94"100mm3.94"110mm4.33"120mm4.72"130mm5.12"
Top Tube Length570mm22.44"595mm23.43"625mm24.61"655mm25.79"682mm26.85"
Seat Tube Angle59°59°59°59°58°58°57.5°57.5°57.5°57.5°
Standover Height730.7mm28.77"731.3mm28.79"728.7mm28.69"728mm28.66"728mm28.66"
Eye to Eye Length

Frame Sizing

s
5'0"152 — 5'4"163cm
m
5'4"163 — 5'8"173cm
l
5'8"173 — 5'11"180cm
xl
5'11"180 — 6'2"188cm
xxl
6'2"188 — 6'5"196cm

Tech Support

Can I mount a chainguide to my bike?

Yes, this bike is equipped with ISCG-05 tabs for easy chainguide mounting.  Most chainguides on the market that are made for this standard should work.

It looks like the lower link is off center in my frame- is everything ok?

Yes- this is correct. With our newer pivot system, the pivot axle draws the link over to one side in order to properly preload the bearings. This offset is accounted for in the frame design so everything ends up nice and straight in the end.

Should I grease the headset cups when I install them?

Yes, we recommend this. Do not use the Carbon Assembly Compound on the headset, as it will make it more difficult to remove from the frame.

What is the torque spec for the seat collar?

We don't provide a torque spec for the seatpost, because it really depends on what seatpost you are using. Some seatposts are slippery, and require more torque to stay put, and others are very thin- and can be crushed by overzealous tightening. Some are both slippery and thin... Make sure you use the Carbon Assembly Compound included with your carbon frame, and use some common sense.

You will not damage your frame by overtightening the seat collar, assuming you have a 30.9mm seatpost in it.

What kind of headset does the V10 use?

The V10 uses a standard 1.5" headtube. We spec a 49mm internal headset (Zero Stack). The SHIS name is ZS49/28.6 ZS49/30.

What kind of rear brake adaptor do I need?

This frame uses a standard IS rear brake mount. Just pick your rotor size and order the correct adaptor to go from IS to post mount (all modern brakes).

What size bottom bracket shell does this bike use?

The V10 uses an 83mm threaded BB. Most downhill cranks are compatible with this standard.

What size hub do I need?

The V10 uses a 157x12mm through-axle rear hub. An axle is included with purchase of a frame or complete bike.

What size seat collar do I need?

Bikes with a 30.9mm seatpost require a 34.9mm seat collar. 

What size seatpost do I need?

We use a 30.9mm seatpost. Always ensure it is inserted into the frame a minimum of 100mm (4").

What size shock does the V10 use?

This generation of the V10 (V10.6) uses an 8.75"x2.75" shock (222x70mm).  Mounting hardware is 22x8mm- or 21.8x8mm if you have a Rockshox shock.